Page 28 - drylinR - Round shaft guide systems

drylin ® R drylin R
®
drylin R | igus |
shaft drylin R shaft guides | igus testing method ® ® ® Notes | shaft
®
guides
guides

Bf Bf
ts
Part No. Test force Øi test housing Min. bearing Øi Max. bearing Øi ts
Øi
(plug gauge sticks)
(plug gauge falls)
[N] [N] db ds [mm] [mm] ( ) [mm] ( ) ds db
XUMO-01-10XUMO-01-10 0.981 0.981 12.000mm12.000mm 9.98mm9.98mm 10.02mm10.02mm
XUM-01/02-12 1.373 d1 d2 1.373 14.000mm14.000mm U 12.02mm12.02mm 12.06mm12.06mm d2 d1 U
XUM-01/02-12
d3
XUM-01-14
XUM-01-14 1.500 1.500 16.000mm16.000mm 14.02mm14.02mm 14.06mm14.06mm
XUM-01/02-16
XUM-01/02-16 1.864 1.864 18.000mm18.000mm 16.02mm16.02mm 16.06mm16.06mm
XUM-01/02-20 2.649 2.649 23.000mm23.000mm 20.03mm20.03mm 20.07mm20.07mm
XUM-01/02-20
B I
-Ø d1
XUM-01/02-25
XUM-01/02-25 3.729 3.729 28.000mm28.000mm J 24.97mm24.97mm 25.01mm25.01mm B
XUM-01/02-30
XUM-01/02-30 4.807 4.807 34.000mm34.000mm 29.96mm29.96mm 30.01mm30.01mm
K 44.000mm44.000mm igl idur ®
XUM-01/02-40 7.063 7.063 40.00mm40.00mm 40.05mm40.05mm
XUM-01/02-40
:
Explanation:
iglidur X iglidur J
®
®
®
®
®
iglidur X iglidur J iglidur X 106 106
to the ratio of test force to LD diameter. The parts are designed in such a way that under load the clearance between the
h
iglidur® X and iglidur® J plain bearings is as identical as possible. Thereby in the use of iglidur® X liners, increased shifting dt
dt
forces can occur in the unloaded new condition on an h-toleranced shaft. d3
When using a plain bearing (e.g. JUM/RJM) in connection with an adapter/ housing (e.g. RJUM, OJUM, RGA) the factory H7
JUM/RJM)
RJUM,OJUM,RGA
tolerance of the housing hole (standard case: H7) is also added to the minimum clearance stated above. The total from
these two values then produces the maximum possible bearing tolerance.
added to give the maximum possible clearance.
F max dynamic: d1 d2 B d3 K Bf dt db ds ts d1-ʮࢨ ࠠඎ d1 d2 B d3 I Bf dt db ds ts d1-ʮࢨ ࠠඎ
˾
:
F
[mm]
The maximum values are the result of the projected surface and 5MPa surface pressure. [g] [mm] [g]
max
5 MPa
FJZM-01-06-LMK 6 12 19 28 22 5 20 3.4 6.5 3.3 +0.020 +0.068 7.04 FJZM-01-06-LMIF 6 12 19 28 5 5 20 3.4 6 3.3 +0.020 +0.068 9.14
F max static: :
F
max
The maximum values are the result of the projected surface and 35MPa surface pressure.
FJZM-01-08S-LMK 8 15 17 32 25 5 14 3.4 6.5 3.3 +0.030 +0.070 9.44
35 MPa FJZM-01-08-LMIF 8 15 24 32 5 5 24 3.4 6 3.3 +0.030 +0.070 14.05
FJZM-01-08-LMK 8 15 24 32 25 5 24 3.4 6.5 3.3 +0.030 +0.070 11.63
Due to the manufacturing process, the anti-rotation feature of the JUM-01/JUM-02-/JUM-11 liners can be either round FJUM-01-10-LMIF 10 19 29 39 6 6 29 4.5 7.5 4.4 +0.030 +0.088 26.31
FJUM-01-10-LMK 10 19 29 39 30 6 29 4.5 8 4.4 +0.030 +0.088 21.07
FJUM-01-12-LMIF 12 21 30 42 6 6 32 4.5 7.5 4.4 +0.030 +0.088 30.92
FJUM-01-12-LMK 12 21 30 42 32 6 32 4.5 8 4.4 +0.030 +0.088 24.64
FJUM-01-13-LMIF 13 23 32 43 6 6 33 4.5 7.5 4.4 +0.030 +0.088 35.63
FJUM-01-13-LMK 13 23 32 43 34 6 33 4.5 8 4.4 +0.030 +0.088 30.15
FJUM-01-16-LMIF 16 28 37 48 6 6 38 4.5 7.5 4.4 +0.030 +0.088 54.45
FJUM-01-16-LMK 16 28 37 48 37 6 38 4.5 8 4.4 +0.030 +0.088 46.66
׼ 1079
FJUM-01-20-LMK 20 32 42 54 42 8 43 5.5 9.2 5.4 +0.030 +0.091 63.12 FJUM-01-20-LMIF 20 32 42 54 8 8 43 5.5 9 5.4 +0.030 +0.091 75.24
Tightening torque for drylin metallic screws drylin ® 59 ® 62 50 8 51 5.5 9.2 5.4 +0.030 +0.091 129.16 FJUM-01-25-LMIF 25 40 59 62 8 8 51 5.5 9 5.4 +0.030 +0.091 142.19
FJUM-01-25-LMK 25 40
Metric thread (Da)
(Da)
6.5 +0.040 +0.110 Recommended tightening torque
FJUM-01-30-LMK 30 45 64 74 58 10 60 tightening torque 168.95 પঢԴٙ͜ҩॉ
11
6.6
[Nm] [Nm] [Nm] [Nm]
FJUM-01-35-LMK 35 52 70 82 64 10 67 6.6 11 6.5 +0.040 +0.110 234.71 0.7 0.7
0.5 – 1.1 0.5 – 1.1
M3
M3
M4
M4
FJUM-01-40-LMK 40 60 80 96 75 13 78 9 1.0 – 2.8 1.0 – 2.8 378.1 1.5 1.5
8.6 +0.040 +0.115
14
M5 M5 2.0 – 5.5 2.0 – 5.5 3.0 3.0
9
8.6 +0.050 +0.130
14
FJUM-01-50-LMK 50 80 100 116 92 13 98 4.0 – 10.04.0 – 10.0 850.3 6.0 6.0
M6
M6
M8
8.0 – 23.08.0 – 23.0
M8
FJUM-01-60-LMK 60 90 110 134 106 18 112 11 17.5 10.8 +0.050 +0.140 1150.96 15.0 15.0
M10 M10 22.0 – 46.022.0 – 46.0 30.0 30.0
: 1.5xDa
Please be aware of the minimal screw-in depth for aluminium and zinc die-casting parts: 1.5xDa
1146 www.igus.com.cn/drylinR 3D/CAD www.igus.com.cn/drylinR 1147