Page 57 - MiSUMi FA Mechanical Components Economy Series
P. 57

1


           2Categories of use                                                              Unit: mm
                                                                     Maximum screw shaft runout tolerance   Lead Screws / Actuators  Ball Screws /
                                                Accuracy Grade
                                                                     (please see the table below for details)
                 MISUMI Economy series               C5                          0.120
                 MISUMI standard product                                         0.080
           Screw shaft runout tolerance                                                               Ball Screws
                                       G
                                                                      Screw shaft overall length
                                                                 ~200   201~315  315~400  401~500    P.31
                                                         MISUMI
                                                         Economy   0.065  0.080   0.100    0.120
           MAX10                        MAX10             series
           (Incomplete                 (Incomplete   G   MISUMI                                      Ball Screws  Precision
            Hardened Area)              Hardened Area)   standard   0.040  0.055  0.065    0.080
                                                         product
                                                                                                     P.49
                Alteration
           2Support side                               2Fixed side                                   for Ball Screw  Support Units
                 Alterations            Spec.                Alterations            Spec.
              No Machining on Support Side                Wrench Flats on Fixed Side  Adds wrench fl ats on the fi xed side
             Shaft End                                                     shaft end.                P.61
                 Standard       No machining added on the support   5  5   &  Ball bearings will fall out if the ball
                                                                             nut crosses the wrench flats.
                                                             0
            When machining      side shaft end.             8-0.2  30      &  The nut may not be moved within
                is specified                                                 the Incomplete Hardened Area.  Brackets  Motor
                          L                             Incomplete Hardened Area
                                                          Keyway on Fixed Side Shaft   Adds a keyway on the fi xed side shaft
             Ball Nut Orientation Reversed               End %P.33         end.                      P.69
              (Support side)  (Fixed side)                                 3≤KC≤14
             Standard           Changes the nut direction.                 When specifi ed simultaneously with 2,
                                                                           3≤KC≤F-1
                                                             KC
             Change                                                        9P = 5 is not applicable   Lead Screws
                                                                           KC = 1mm increments
              No Retaining Ring Groove on                 Machining fi xed side shaft end   The machining position of keyways at
             Support Side Shaft End                      keyways           fi xed side shaft end can be specifi ed.   P.71
                                                                           (Keyway size is the same as KC.)
                                No Retaining Ring Groove on Support        3≤K≤13  K+S≤14
                  Standard
             When machining     Side Shaft End.                K   S       When specifi ed simultaneously with 2,  3≤K≤22
                 is specified                                                                K+S≤F-1  Nuts  Lead Screw
                                                                           9P = 5 is not applicable
                                                                           K, S = 1mm increments
              Change Support Side Shaft
             End Machining      Changes the machining on the      Flat Machined on Fixed Side   Adds a fl at on the fi xed side shaft end  P.83
                                                         Shaft End
                Standard        support side.                              5≤SC≤14
            When machining      5≤G≤24                                     When specifi ed simultaneously with
                                Choose Q from 6 and 8
               is specified  Qh7  G  G = 1mm increments       SC    0.5    2, 5≤SC≤F-1               Support Units   Lead Screw
                                                                           SC = 1mm increments
              Change Support Side Shaft                   No machining of small steps on
             End Length                                  the fi xed side
                                Change the length of the support side   Standard                     P.86
                                shaft end.                                 No machining of small steps on the
                     7.9        10≤FC≤20                   Change          fi xed side
                  FC            FC = 1mm increments
                                                                    L                                Stop Plates  Lead Screw
                                                       2  Change dimensions of small
           & Only one of  ,  ,   and   can be selected.  steps on the fi xed side
           & Only one of  ,   and   can be selected.                       Change dimensions of small steps on   P.90
           &    and 2 cannot be specifi ed simultaneously.  Recommended     the fi xed side
           & When 8 and F are specifi ed simultaneously, no male thread will be   P  15≤F≤24  5≤P≤8
             machined regardless of the value specifi ed for U in 8.        F, P = 1mm increments
           & When 8 or F is specifi ed, the recommended support unit may not be   F                    Actuators
             available. Please reconfi rm.              8  Change dimensions of big
           & When specifying any alteration, the nut motion range (Y dimension)   steps on the fi xed side
             may become shorter. Please make sure that the nut motion range is   Change dimensions of big steps on
             greater than the full length of the nut.   Recommended  U     the fi xed side            P.99
                                                                           11≤E≤40  8≤U≤E-3
                                                                           E, U = 1mm increments
                                                                  E
                                                       F  No machining of big steps male
                                                        thread on the fixed side
                                                                           No machining of big steps male
                                                           Standard        thread on the fi xed side
                                                            Change
                                                                                                    54
   52   53   54   55   56   57   58   59   60   61   62