Page 36 - MiSUMi FA Mechanical Components Economy Series
P. 36

1     Economy Series       Alteration Options / Precautions
            Ball Screws
      Ball Screws /  Lead Screws / Actuators  2Although the machining is   2Alteration Options



           carried out according to the

                                                                                fixed side shaft end
                                                           support side shaft end
       Ball Screws  standard shaft end by default, there   ·Alteration options for the   ·Alteration options for the
           are a variety of alterations that can
                                                                                   Wrench Flats on
                                                           No Machining on Support
           be specified.
                                                                                     Fixed Side
                                                               Side Shaft End
     P.31  ·Both the support side and the fixed side are
           shipped after machining according to the assembly
           dimensions with the applicable support unit.
      Precision   Ball Screws                                Ball Nut Orientation   Adds a keyway on the fixed
                                                                                     code: SZC
                                                                code: NC
                                                             (Support side)
     P.49                                                 Standard  Reversed (Fixed side)  side shaft end.
      Support Units   for Ball Screw                       Change  code: RLC          code: KC
     P.61                                                 No Retaining Ring Groove on   Machining fixed side shaft
                                                            Support Side Shaft End
                                                                                    end keyways
      Motor   Brackets                                     Standard
                                                            Change
           ·Detailed dimension of alteration KC·KLC keyway
                                                                                      code: KLC
                                                                code: RNC
     P.69          b                   b       t            Change the machining   Flat Machined on Fixed
       Lead Screws  6.33  t    Shaft  Reference Tolerance Reference  Tolerance  content of the support side  Side Shaft End
                               Dia.
                                           dimension
                                   dimension
                                        (N9)
                               6~7
                                       -0.029
                               8~10
                                            1.8
     P.71                      11~12  2 3 4  -0.004  1.2  +0.1  code: GC              code: SC
                                            2.5
      Lead Screw   Nuts        13~17  5 6  -0.03  3.0      Change Support Side Shaft
                                                0
                                        0
                                            3.5
                               18~20
                                                               End Length
     P.83                                                        code: FC
      Lead Screw   Support Units   2Precautions on Handling  *For details of the machining content, please visit MISUMI official website.
     P.86    (1) If the nut is removed from the screw shaft, the ball will fall off   (6) In operation, if there is too much noise or sharp and harsh
      Lead Screw   Stop Plates  the nut and cannot be used.   (7) Although lithium soap-based grease has been applied at
                                                            sound, please make sure that the installation accuracy of
                                                            the screw and the specifications of peripheral components
                Do not disassemble, as this may cause impurities to enter the
                interior and damage the assembly accuracy of each part. When
                                                            such as motors and couplings are appropriate.
                the nut needs to be removed, use a special auxiliary shaft.
     P.90    (2) The outer circle, spiral groove and circulating parts of the screw   the factory, it is required to apply new grease every 2~3
                                                            months as standard after receiving the goods.
                shaft will be damaged by external force impact, resulting in poor
                circulation and loss of function. Please take care to avoid it.  (8) Do not let the nut exceed the movement range of the ball
       Actuators  weight. Please be careful. Especially when it is used as a   (9) Nut overstroke operation is prohibited.
                                                            screw nut, or screw out of the screw shaft, otherwise the
             (3) Ball screws and nuts placed with an inclination may fall due to
                                                            ball will fall off and the ball cycling parts will be damaged.
                vertical axis, the nuts are likely to fall due to weight. Please set
                up a fall prevention mechanism.
                                                            patterns and color difference in its appearance. Small
     P.99    (4) Please check the flexibility by rotating the screw shaft with the   (10) This product is a machined type, so there will be knife
                fixed nut or rotating the nut with the fixed shaft.  scratches or color changes without affecting the use and
             (5) Rotating the nut by hand may not feel smooth, but does not   main function are a normal phenomenon. Please feel free
                affect the positioning precision. Please feel free to use.  to use.
                                                          (11) The noise value of the screw after assembly is not
                                                            guaranteed.
                                                          If the nut end face is moved out of
                                                          the range of right figure, it will
                                                          cause the ball to fall off, resulting in
               Removal of  No impact on   Be careful of falling  Checking for
              nut is prohibited  the nut  due to weight  reverse action  malfunction.
      33
   31   32   33   34   35   36   37   38   39   40   41