Page 81 - MiSUMi FA Mechanical Components Economy Series
P. 81

1



                Alteration                                                                           Lead Screws / Actuators  Ball Screws /

                        Flat Machining           Retaining Ring Groove             Wrench Flats
                             V(Q)                      n                                 V(Q)
            Alterations                            V(Q)  e                                            Ball Screws
                       FY  FV   FW                   m     AC(AQ)               SW     SC    SY
                            (FQ)                        F  (S)
                                                                                       (SQ)          P.31
                      FV, FQ, FW, FY =  AC, AQ =                       + 0.14  Machining  SC, SQ, SW, SY =
                      0.5mm increments  0.1mm increments  V·Q e tolerance m 0 n limit  1mm increments
                                                          6
                      FV =  Applied on   AC,AQ≤F(S)-m-n   7  4  + 0.075  0.7   SC = Applied on Part V  Ball Screws  Precision
                          Part V      Machining limit     8  5   0       n≥1.2  SQ = Applied on Part Q
                      FQ =  Applied on  AC = Applied on Part V,   9  6  0.9    &  Applicable to either
                          Part Q      AQ = Applied on Part Q    0               V or Q               P.49
              Spec.   &  Applicable to either            10  9.6  -0.09        &  When Q(V)<15
                        V or Q                           12 11.5                 SW≥Q(V)-2
                      FY≤1.0                             14 13.4      1.15 n≥1.5  &  When 15≤Q(V)≤17  for Ball Screw  Support Units
                      &3≤FW≤20                           15 14.3  0              SW≥Q(V)-3
                                                         16 15.2  -0.11        &3≤SY≤20
                                                         17 16.2                                     P.61
                                  Coarse Tapping                     Threaded For Bearing Nut
                                 MC        MQ                           For bearing nut              Brackets  Motor
                                                                            Q(V)  M
            Alterations
                                V                Q                                                   P.69
                                   MC×2   MQ×2                                BC
                                                                             (BV)                     Lead Screws
                      MC = Applied on Part V                &BV,BC≤M×3           V·Q  M×Pitch
                      MQ = Applied on Part Q                &BV,BC≥Pitch×3        6  M6×0.75
                       V·Q  MC·MQ (Selection range)         &BV,BC≤F,S-Pitch×3                       P.71
                        6  3                                BV = Applied on Part V  8  M8×1.0
                       7·8  3·4                   Must be more   BC = Applied on Part Q  10  M10×1.0
                       9·10 3·4·5                 than 1mm                       12  M12×1.0         Nuts  Lead Screw
              Spec.     12  3·4·5·6                                              14  M14×1.0
                       14·15 3·4·5·6·8            Other alteration
                       16·17 3·4·5·6·8·10         Tapped hole                    15  M15×1.0         P.83
                      &Keep the wall thickness more than 1mm.                    17  M17×1.0
                        Otherwise you can not choose this alternation.          9V, Q = 7·9·16 is not
                                                                                  applicable         Support Units   Lead Screw
                                 Square Chamfering                         Keyway
                                          V(Q)                           CKC(KV) 1.6  b1             P.86
            Alterations
                                       -0.1                                     3.2    t1            Stop Plates
                                       W -0.3  A                              Q(V)                    Lead Screw
                                         F(S)
                                    3.2                                              r1
                      W, A = 1mm increments                 KC, KV, C = 1mm increments  Applicable  Keyway Dimension  P.90
                      ZC = Applied on Part V  ZC=V  W       KV = Applied on Part V  shaft   b1  t1
                      ZQ = Applied on Part Q  ZQ=Q 1mm increments  KC = Applied on Part Q  diameter Reference Tolerance Reference   r1
                      &Applicable to either   6·7   5       &  Applicable to either   V·Q dimension  (N9) dimension Tolerance  Actuators
                        V or Q              8       6          V or Q
                      &5≤A≤20               9       7       &C≤60            6·7  2  -0.004  1.2
              Spec.   & Specifi ed by ZC=V,   10     8       &S(F)-C-KC(KV)≥2        -0.029     0.08  P.99
                        ZQ=Q                12     9 10     &KC(KV)≥2        8~10  3    1.8  +0.1 ~0.16
                                          14·15   10 11 12  &When KC, KV=0    12  4     2.5  0
                                            16    11 12 13                          0
                                            17    12 13 14                          -0.030     0.16
                                                              C              14~17  5   3.0   ~0.25

               Registration  Technical Support  Sales Inquiry  Contact Us:
                                                            Tel:           (60)3 7960 8499
                                                            Email:         cs@misumi.com.my
                                                            Operation Hour:  9am-6pm (Mon - Fri)
                                                                           9am-1pm (Sat)            78
   76   77   78   79   80   81   82   83   84   85   86