Page 78 - MiSUMi FA Mechanical Components Economy Series
P. 78

1     Economy Series       Alteration Options
            Economy Series
            Lead Screws
            Product Overview Lead Screws
      Ball Screws /  Lead Screws / Actuators  2Alteration Options





       Ball Screws  Machining                            Threaded For
               Flat


     P.31                                                 Bearing Nut
      Precision   Ball Screws  Wrench Flats



     P.49                                                  Square
      Support Units   for Ball Screw  Retaining           Chamfering




     P.61    Ring groove
      Motor   Brackets

              Coarse
              Tapping                                      Keyway
     P.69
       Lead Screws                                                       2Machining conditions for




     P.71  2Precautions for Selecting Alteration  Precaution    Precaution    combining "square
                                                                           chamfering" and "coarse
                            Precaution
              Precaution
      Lead Screw   Nuts  Reserve a gap of   The interval   The phase of each machining is   Specifying alteration   Shaft end  Square   Tapping
                                                                           tapping"
                                                                                          Coarse
                                                                              Square
            2mm or more from
                                        random and may not be aligned in
                          between the
                                                          which overlaps another
                                                                            Chamfering
                          alterations must be
                                                          machining is unavailable.
                                        a row ,when multiple alterations
            the stepped part
            to specify the
                          more than 2mm
                                        are specified. (The following figure
                                                          (The following figure shows
                                                                                 Width/W
     P.83   alteration          Must be  shows one of the examples)  one of the NG examples)  diameter  Chamfering   Tap Dia.
                                                                Alteration A
                                                                                  5~8
                                                                           6~10
                                                                (Keyway)
                                                                                            3
      Lead Screw   Support Units   than 2mm  more than  (Wrench Flats)  Phase  Rotation  Rotation  11~14  8~10  3·4
                                                   Alteration B
                Must be more
                                                    (Keyway)
                                2mm
                                        Alteration A
                                                                    direction
                                                              Alteration B
                                                   direction
                                 Alteration B
                  Alteration
                                                              (Flat Machining)
     P.86      Stepped Part   Alteration A  As shown in the above figure,   The overlap position   15~19  10~14  3·4·5
                                        phases are random,so the
                                        alteration A and B on the
                                                            of alteration A, B
      Lead Screw   Stop Plates  (1) When specifying the alteration position, reserve a gap of 2mm or more from the stepped part (refer to the illustration of Precaution  ).
                                        same axis may not be aligned
                                                                           20~25
                                                                                 14~20
                                                                                          3·4·5·6·8
                                        in a row.
           (3) When combined with Flat Machining, Wrench Flat, Square Chamfering, and Keyway, each machining phase is random.
     P.90  (2) When multiple alterations are selected, the machining parts need to be spaced by more than 2mm (refer to the illustration of Precaution  ).
              (refer to the illustration of Precaution  ).
           (4) When 2 or more alterations are specified on the same shaft part, it may not possible to machine due to the correlation.
       Actuators  (5) Specifying alteration which overlaps another machining is unavailable. (refer to the illustration of Precaution  ).
           2Precautions for use
     P.99
              1. Do not drop or knock the trapezoidal screw. Otherwise it may cause scratches or damages. Attention
               should be paid to the fact that impact can cause functional damage, even if it is not visible.
              2. When contacting the product, please use protective gloves, safety shoes and other protective
               equipment to ensure safety.
      75
   73   74   75   76   77   78   79   80   81   82   83